Hot compression and fracture toughness of HSS composed hot strip work rolls

The rolls in the finishing stands must have good resistance to both wear and fire cracks. The use of high-speed steel at the finishing stands has shown satisfactory results. The composition of this high-alloyed steel is an important parameter as the most significant change lays on the type, morphology, and volume fraction of the eutectics carbides. The heat treatment of these products consists of high temperature austenization followed by quenching and two temperings, as required in order to increase their overall hardness and to completely eliminate residual austenite. The influence of tempering temperatures on the mechanical properties of these products, determined using tensile, hot compression and fracture toughness tests, was studied in this research work. Their corresponding failure micromechanisms were defined by means of the analysis of fracture surfaces.     

Analysis of fracture behaviour of the cement mantle of reconstructed acetabulum

In this study, the finite element method was used to analyse the crack behaviour in the cement of a reconstructed acetabulum by computing the stress intensity factors at the crack tip. Three loading cases were examined (Fig. 6). These cases present the different human body postures. Both positions and orientations of crack effect on the SIF variation were analysed. When valuating the crack position effect, one notices no risk of crack propagation under the load type 1; however, under the load type 2 and the load type 3 this risk is more important. Load type 3 is the most dangerous loading condition. When computing crack orientation, one noted that the risk of crack propagation is higher when the crack inclination is 20° and 100°.     

A theoretical analysis of flexional bending of Al/Al2O3 S-FGM thick beams

In this paper, an elastic, rectangular, and simply supported, sigmoid functionally graded material (S-FGM) beam of thick thickness subjected to uniformly distributed transverse loading has been investigated. The S-FGM system consists of ceramic (Al₂O₃) and metal (Al) phases varying through the thickness of beam. Major classes of representative theories such as classical laminate beam theory (CLBT), first-order shear deformation theory (FSDT) and high-order theories (HOTs) have been considered and a unified kinematic formulation is then proposed. The Poisson’s ratio of the thick S-FGM beam is assumed to be constant, but their Young’s moduli vary continuously throughout the thickness direction according to the volume fraction of constituents defined by sigmoid function. The numerical illustrations concern bending response of S-FGM rectangular beams. Qualitative and quantitative assessments of displacement and stress fields have been presented and discussed.     

Elastic–plastic analysis of interaction between an interfacial crack and a subinterfacial microcrack in bi-materials

In the present work the finite element method is used to analyze the effect of interaction between an interfacial crack and a microcrack in ceramic/aluminum bi-materials. The behaviour is analyzed by the determination of the J integral, the plastic zone at the tips of the interfacial crack and the microcrack. The effects of longitudinal and transversal distance between the tips of the two cracks and the rotation of the microcrack are examined. The obtained results allow us to deduce a correlation between the position of the microcrack and the J integral and the plastic zone.The obtained results shows that the J integral at the interfacial crack tip reaches a maximum value when the microcrack is moved in the vicinity of the interfacial crack. With this distance the effect of interaction is marked more; the stress field at the microcrack tip and that of the interfacial crack generates only one plastic zone at the interfacial crack tip. The maximum size of the plastic zone is localised at the interfacial crack tip. Those of the two tips of the microcrack are very weak and even negligible in front of the zone plasticized at the interfacial crack tip.     

Dynamic joint resource allocation and relay selection for 5G multi-hop relay systems

LTE/LTE-A networks have become widely exploited to address the increasing demands of mobile traffic. Relay technologies have recently been introduced to fulfill such requirements. Currently, the LTE-A relay standard is restricted to two-hop relaying. This architecture minimizes system complexity, but multi-hop relay architecture could potentially provide greater capacity and coverage in the future. However, many complexities of the multi-hop relaying paradigm must be resolved. In this work, we focus on downlink resource allocation and relay selection, by which a user may be connected to a base station through a multi-hop relay and have several relay stations from which to choose within his range. To overcome the additional challenges introduced by multi-hop relay nodes, we propose a dynamic joint resource allocation and relay selection scheme. Numerical results are presented to demonstrate the validity of the proposed algorithm.     

Brazilian disk test simulation intended for the study of interfacial cracks in bi-materials

The good mechanical characteristics of bimaterials and in particular those of the ceramic-metal couple would make them, industrially, an interesting alternative if their fracture behaviour was better understood. The difference of the mechanical properties of the bonded materials leads to a stress concentration at the vicinity of the interface. This study concerns the analysis of the interfacial fracture in Brazilian disk test, subjected to compressive load. The finite element method is used to carry out this objective. The study is limited to the case of an elastic behaviour of the two components of the assembly and to a pure junction. The behaviour of a crack located at the interface is analyzed by global approach based on the strain energy release rate. The difference of the mechanical properties of the two bonded materials leads to a mixed mode (mode I + II).     

Infection with Chlamydia trachomatis alters the tyrosine phosphorylation and/or localization of several host cell proteins including cortactin

Infection of epithelial cells by two biovars of Chlamydia trachomatis results in the tyrosine phosphorylation of several host proteins. The most prominent change in host protein tyrosine phosphorylation involves a complex of proteins with molecular masses of 75 to 85 kDa (pp75/85) and 100 kDa (pp100). The C. trachomatis-induced tyrosine phosphorylation of pp75/85 and pp100 is observed in several cell lines, including epithelial cells, fibroblasts, and macrophages. Subcellular fractionation and detergent solubility properties of pp75/85 are consistent with its association with the cytoskeleton. Phosphoamino acid analysis demonstrates that the pp75/85 complex is phosphorylated on both tyrosine and serine residues. Immunofluorescence studies of chlamydia-infected cells by using fluorescein isothiocyanate-phalloidin and antibodies to phosphotyrosine and cortactin demonstrate that tyrosine-phosphorylated proteins, as well as cortactin, are localized to the chlamydial vacuole and that this process is facilitated by actin.     

Etude des propriétés rhéologiques de mélanges fondues de polybutène-1 et de polypropène à des cisaillements élevés

The viscoelastic behaviour of polybutene-1-polypropene blends has been studied in the molten state with respect to temperature, shear stress and shear rate. The corrections of experimental data have been carried out and the influence of the radius of capillary on these corrections was studied. The elasticity was investigated by means of Barus factor and the variation of viscosity versus composition of blends shows a minimum which might be interesting for the technology of plastic materials.     

A mixed mode crack growth model taking account of fracture surface contact and friction

Fracture surface interactions, of whatever origin, can significantly affect the stress intensity factor, and consequently, can also be relevant to fatigue crack propagation. In the occurrence of interaction between fracture surfaces, the effective loading cycle experienced by material near the crack tip may be very different from that evaluated on the basis of the external loadings only. The purpose of the work described in this paper is to obtain the effective mode II stress intensity factor, k _IIeff, in a surface cracked elasto-plastic plate with a factory roof fracture surface subjected to an in-plane shear (mode II) loading. A new model estimating the magnitude of the frictional mode II stress intensity factor, k _f, arising from the mismatch of the fracture surface roughness during in-plane shear, is developed. Furthermore, the results of this study are employed in modeling the fatigue response of the surface cracked plates subjected to mixed mode loading.